2000 Acura RL 3.5 Service Manual

The 2000 Acura RL 3.5 Service Manual provides comprehensive technical information for the 3.5L V6 engine model, covering maintenance procedures, specifications, troubleshooting, and repair guidelines. This manual includes engine systems, transmission, suspension, brakes, electrical systems, heating/AC, and body components. Below are key sections for maintenance schedules, specifications, service procedures, and troubleshooting.

Vehicle Specifications

Key technical data for the 2000 Acura RL 3.5L model.

Maintenance Schedule

Recommended service intervals for optimal performance.

1. Oil and filter change: Every 7,500 miles or 12 months
2. Air filter replacement: Every 30,000 miles
3. Spark plugs: Replace every 105,000 miles
4. Timing belt: Replace every 105,000 miles
5. Brake fluid: Replace every 3 years
6. Coolant: Replace every 5 years or 60,000 miles
7. Transmission fluid: Replace every 30,000 miles

WARNING! Always use genuine Acura parts and fluids for optimal performance and warranty compliance.

Engine Service

Procedures for 3.5L V6 engine maintenance and repair.

1. Oil change procedure: Drain plug torque 29 lb-ft, filter torque 13 lb-ft
2. Spark plug replacement: Gap 0.039-0.043 inches, torque 13 lb-ft
3. Timing belt replacement: Requires special tools, follow alignment marks
4. Valve adjustment: Cold engine, intake 0.008-0.009 in, exhaust 0.010-0.011 in
5. Cooling system: Burp system after service to remove air pockets

CAUTION! Engine must be cool before performing service. Use proper safety equipment.

Transmission Service

Automatic transmission maintenance and troubleshooting.

• Fluid Type: Honda/Acura ATF-Z1
• Fluid Capacity: 7.4 quarts (complete change)
• Fluid Change: Drain and refill every 30,000 miles
• Filter Service: Replace fluid filter during transmission service
• Shift Points: 1-2: 15 mph, 2-3: 25 mph, 3-4: 45 mph

Brake System

4-wheel disc brake system service procedures.

Front Brakes: Rotor minimum thickness 0.87 in, Pad minimum 0.12 in

Rear Brakes: Rotor minimum thickness 0.35 in, Pad minimum 0.12 in

Brake Fluid: DOT 3 or DOT 4, replace every 3 years

ABS System: Use Honda diagnostic system for troubleshooting

Suspension & Steering

Double-wishbone suspension and power steering maintenance.

1. Wheel alignment: Front toe 0±0.08 in, Camber -0°30'±45'
2. Ball joints: Check for play during tire rotation
3. Struts/shocks: Replace if leaking or excessive bounce
4. Power steering: Use Honda power steering fluid only
5. Tire pressure: 32 psi front and rear

Tip: Always perform wheel alignment after suspension component replacement.

Electrical System

Battery, charging, and electrical component service.

1. Battery: 12V 60Ah, located in trunk, clean terminals regularly
2. Alternator: Output 110A, test if battery discharge issues
3. Starter: Draw test maximum 180A
4. Fuses: Main fuse 100A, under-hood fuse box
5. Bulb replacement: Headlights 9006/9005, follow proper aiming procedure

WARNING! Disconnect battery negative terminal before electrical work to prevent shorts.

Heating & AC

Climate control system service and maintenance.

Refrigerant: R-134a, Capacity 1.76 lbs

Compressor Oil: ND-OIL 8, 5.4 oz

AC Service: Evacuate and recharge system if performance poor

Heater Core: Flush if insufficient heat

Body & Interior

Exterior and interior component maintenance.

• Paint Care: Use mild soap, avoid abrasive cleaners
• Leather Care: Use Honda/Acura leather conditioner
• Window Regulators: Lubricate tracks with silicone spray
• Sunroof: Clean drain tubes annually
• Door Seals: Apply silicone grease to prevent sticking

Troubleshooting

Diagnostic Codes: Use OBD-II scanner to retrieve trouble codes

Service: Contact Acura dealer for complex electrical issues