2000 Acura TL Shop Manual

The 2000 Acura TL Shop Manual provides comprehensive technical information for the 2000 Acura TL model, including detailed service procedures, maintenance schedules, troubleshooting guides, and technical specifications. This manual covers the 3.2L V6 engine, automatic transmission, electrical systems, suspension, brakes, and all major components. Below are key sections for maintenance, repair procedures, specifications, and troubleshooting.

1. Vehicle Specifications 2. Maintenance Schedule 3. Engine Service 4. Transmission Service 5. Electrical Systems 6. Brake System 7. Suspension & Steering 8. Heating & AC 9. Body & Interior 10. Diagnostic Procedures 11. Troubleshooting

Vehicle Specifications

Key technical specifications for the 2000 Acura TL model.

Specification	Description
Engine Type	3.2L SOHC V6
Horsepower	225 hp @ 5600 rpm
Torque	216 lb-ft @ 4700 rpm
Transmission	4-Speed Automatic
Fuel System	Programmed Fuel Injection (PGM-FI)
Fuel Capacity	17.2 gallons
Brake System	4-wheel disc with ABS
Suspension	4-wheel independent double-wishbone
Curb Weight	3,483 lbs
Wheelbase	108.1 inches

Maintenance Schedule

Recommended maintenance intervals and service procedures.

Oil Change: Every 7,500 miles or 12 months
Air Filter: Replace every 30,000 miles
Spark Plugs: Replace every 105,000 miles
Timing Belt: Replace every 105,000 miles
Brake Fluid: Replace every 3 years
Coolant: Replace every 5 years or 60,000 miles

WARNING! Always use genuine Acura parts and fluids for optimal performance and warranty compliance.

Engine Service

Detailed procedures for engine maintenance and repair.

Oil Change: Drain plug torque 29 lb-ft, filter torque 12 lb-ft
Spark Plug Replacement: Gap 0.039-0.043 inches, torque 13 lb-ft
Timing Belt Replacement: Requires special tools, follow precise alignment marks
Valve Adjustment: Cold engine, intake 0.008-0.009 in, exhaust 0.009-0.010 in
Cooling System: Burp system after service to remove air pockets

CAUTION! Engine components operate at high temperatures; allow cooling before service.

Transmission Service

Transmission Fluid: Honda ATF-Z1, capacity 2.9 quarts
Fluid Change Interval: Every 30,000 miles
Filter Replacement: With fluid change
Shift Solenoids: Test resistance 12-25 ohms
Transmission Mounts: Inspect for wear and cracking
Shift Cable Adjustment: Critical for proper gear engagement

Electrical Systems

Battery, charging, starting, and accessory systems.

Battery: 12V 60Ah, negative ground. Alternator: 110A output. Starter: 1.4 kW.

Fuse Box Locations: Under-hood main fuse box, interior fuse panel under dashboard. Wiring Diagrams: Color-coded schematics for all circuits. ECU Locations: Main ECU under passenger dash, transmission ECU integrated. Sensor Testing: Procedures for all major sensors including MAP, TPS, CKP, CMP.

Brake System

Hydraulic brake system with ABS service procedures.

Brake Pad Replacement: Front and rear specifications differ
Rotor Specifications: Minimum thickness measurements provided
Brake Fluid: DOT 3 or DOT 4, bleed sequence RR-LR-RF-LF
ABS Service: Special procedures for hydraulic modulator
Parking Brake: Cable adjustment procedures

Tip: Always clean brake components with brake cleaner before assembly.

Suspension & Steering

Front and rear suspension service, alignment specifications.

Strut Replacement: Requires spring compressor tool
Ball Joint Inspection: Check for play and boot condition
Wheel Bearing: Service procedures and torque specifications
Alignment Specs: Camber, caster, and toe settings provided
Power Steering: Fluid type and bleeding procedure
Tie Rod Ends: Replacement and adjustment procedures

WARNING! Use proper spring compression tools for strut service to prevent injury.

Heating & AC

Climate control system service and refrigerant handling.

Body & Interior

Body panel replacement, interior trim, and electrical accessories.

CAUTION! Follow proper procedures for airbag system service to prevent accidental deployment.

Diagnostic Procedures

OBD-II diagnostic trouble codes and system testing.

DTC Retrieval: Use scan tool or paper clip method for flash codes. System Tests: Step-by-step diagnostic procedures for all major systems. Sensor Values: Normal operating ranges for all sensors. Wiring Tests: Continuity and voltage drop testing procedures.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Battery, starter, fuel pump	Check battery voltage, listen for fuel pump, test starter circuit.
Transmission slips	Low fluid, worn clutches	Check fluid level and condition, test line pressure.
ABS light on	Wheel sensor, modulator	Scan for codes, test wheel sensor resistance and output.
Overheating	Thermostat, water pump	Check coolant level, test thermostat operation, inspect water pump.
Electrical issues	Ground connections, fuses	Check all ground points, test fuses and relays.

Reset Procedures: ECU reset, maintenance minder reset procedures.

Technical Support: Acura technical service bulletins and updates available through dealer network.