2001 Acura CL Type S Repair Manual

The 2001 Acura CL Type S is a premium sports coupe featuring a 3.2L V6 engine producing 260 horsepower, 5-speed automatic transmission with SportShift, leather interior, premium audio system, and advanced suspension. This repair manual covers comprehensive maintenance procedures, troubleshooting guides, and technical specifications for proper servicing and repair.

1. Vehicle Specifications 2. Maintenance Schedule 3. Engine System 4. Transmission 5. Brake System 6. Suspension & Steering 7. Electrical System 8. Heating & AC 9. Body & Interior 10. Diagnostic Procedures 11. Troubleshooting

Vehicle Specifications

Complete technical specifications for the 2001 Acura CL Type S.

Specification	Details
Engine	3.2L SOHC V6 VTEC
Horsepower	260 hp @ 6100 rpm
Torque	232 lb-ft @ 3500-5500 rpm
Transmission	5-speed automatic with SportShift
Drivetrain	Front-wheel drive
Brakes	4-wheel disc with ABS
Suspension	4-wheel independent double wishbone
Fuel Capacity	17.2 gallons
Curb Weight	3,505 lbs
Wheelbase	106.9 inches

Maintenance Schedule

Recommended maintenance intervals for optimal performance.

Oil Change: Every 7,500 miles or 12 months
Transmission Fluid: Every 30,000 miles
Brake Fluid: Every 3 years regardless of mileage
Coolant: Every 60,000 miles or 5 years
Spark Plugs: Every 105,000 miles
Timing Belt: Every 105,000 miles or 7 years

WARNING! Always use genuine Acura parts for optimal performance and warranty compliance.

Engine System

3.2L V6 VTEC engine service and repair procedures.

Engine Removal: Disconnect battery, drain fluids, remove accessories
Timing Belt Replacement: Align timing marks, tension properly
Valve Adjustment: Cold engine procedure, proper clearance specs
Oil System: Oil pump replacement, pressure testing
Cooling System: Radiator, thermostat, water pump service

CAUTION! Always relieve fuel pressure before servicing fuel system components.

Transmission

Type: 5-speed automatic with SportShift manual mode
Fluid Capacity: 7.2 quarts (drain and refill)
Fluid Type: Honda/Acura ATF-Z1 or equivalent
Service: Fluid changes every 30,000 miles recommended
Diagnosis: Use Honda Diagnostic System (HDS) for codes
Shift Solenoids: A, B, C, D, E locations and testing procedures
Torque Converter: Lock-up clutch operation and testing

Brake System

4-wheel disc brakes with ABS and electronic brake distribution.

Front Brakes: 11.8-inch ventilated discs, dual-piston calipers. Rear Brakes: 11.1-inch solid discs, single-piston calipers.

Brake Pad Replacement: Remove caliper, compress piston, install new pads. Rotor Service: Minimum thickness 0.94 inches front, 0.35 inches rear. ABS Diagnosis: Wheel speed sensor testing, modulator service, bleeding procedure.

Suspension & Steering

Double wishbone suspension front and rear with vehicle stability assist.

Front Strut Replacement: Support control arm, remove knuckle bolts
Rear Suspension: Multi-link design, camber adjustment procedure
Steering Gear: Power rack-and-pinion, fluid specification
Alignment Specs: Camber, caster, toe settings for optimal handling

Tip: Always check ball joints and bushings during suspension service.

Electrical System

Comprehensive electrical system diagnosis and repair.

Battery: 12V 60Ah, located in trunk, proper jump-start procedure
Alternator: 110A output, voltage regulator testing
Starter: Removal requires intake manifold removal on V6 models
Fuse Boxes: Under-hood and driver's side interior locations
Wiring Diagrams: Color-coded schematics for all circuits
ECU Locations: PCM, ABS, SRS module locations and access

WARNING! Disconnect battery before servicing electrical components to prevent shorts.

Heating & AC

Automatic climate control system service and repair.

Refrigerant: R-134a, capacity 1.54 lbs. Compressor: Variable displacement type, magnetic clutch. Heater Core: Dashboard removal required for replacement. Blower Motor: Under dash passenger side, resistor testing procedure.

Body & Interior

Body panel replacement and interior component service.

Door Panel Removal: Hidden screw locations, clip positions. Seat Service: Power seat motor replacement, memory function calibration. Glass: Windshield replacement procedure, molding installation. Trim: Proper removal techniques to avoid damage.

Diagnostic Procedures

Using diagnostic tools and interpreting trouble codes.

System	Diagnostic Tool	Common Codes
Engine	HDS or OBD-II scanner	P0300-P0306 (misfire), P0420 (catalyst)
Transmission	HDS required	P0700, P0730 (gear ratio), P2714 (pressure)
ABS	HDS or capable scanner	11-xx wheel sensor, 31-xx pump motor
SRS	HDS required	11-xx driver airbag, 21-xx passenger

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine misfire	Spark plugs, coils, fuel injectors	Check compression, replace plugs/coils, clean injectors
Transmission slipping	Low fluid, worn clutches	Check fluid level/condition, pressure test, rebuild
Brake vibration	Warped rotors, stuck calipers	Resurface or replace rotors, service calipers
Electrical issues	Battery, alternator, grounds	Load test battery/alternator, clean ground connections
AC not cooling	Refrigerant leak, compressor	Pressure test system, repair leaks, replace compressor

Reset: Clear codes with HDS after repairs completed.

Service: Contact Acura dealer for technical support and genuine parts.