2008 Acura MDX Repair Manual PDF

The 2008 Acura MDX Repair Manual provides comprehensive technical information for maintenance, repair, and troubleshooting of the 2008 Acura MDX luxury SUV. This manual covers engine systems, transmission, suspension, brakes, electrical systems, HVAC, and body components for the 3.7L V6 engine model with automatic transmission. Below are key sections for maintenance procedures, specifications, troubleshooting, and repair instructions.

1. Vehicle Specifications 2. Maintenance Schedules 3. Engine Systems 4. Transmission & Drivetrain 5. Suspension & Steering 6. Brake Systems 7. Electrical Systems 8. HVAC & Climate Control 9. Body & Interior 10. Diagnostic Procedures 11. Troubleshooting Guide

Vehicle Specifications

Technical specifications for the 2008 Acura MDX including engine, transmission, dimensions, and capacities.

Specification	Description
Engine Type	3.7L SOHC V6 VTEC
Horsepower	300 hp @ 6000 rpm
Torque	275 lb-ft @ 5000 rpm
Transmission	5-speed automatic with SportShift
Drivetrain	Super Handling All-Wheel Drive (SH-AWD)
Fuel Capacity	21.0 gallons
Curb Weight	4,486 lbs
Overall Length	190.7 inches
Wheelbase	108.3 inches
Towing Capacity	5,000 lbs (with accessory towing package)

Maintenance Schedules

Recommended maintenance intervals and service procedures for optimal vehicle performance.

Oil and filter change: Every 7,500 miles or 12 months
Tire rotation: Every 7,500 miles
Air filter replacement: Every 30,000 miles
Transmission fluid: Replace every 30,000 miles
Spark plugs: Replace every 105,000 miles
Brake fluid: Replace every 3 years
Coolant: Replace every 120,000 miles or 10 years

WARNING! Always use genuine Acura parts and fluids for optimal performance and warranty compliance.

Engine Systems

Comprehensive engine repair and maintenance procedures for the 3.7L V6 powerplant.

Engine Removal: Step-by-step procedure for engine removal and installation
Cylinder Head: Removal, inspection, and installation procedures
Timing Belt: Replacement procedure and tension adjustment
Fuel System: Fuel pump, injectors, and pressure regulator service
Ignition System: Spark plug replacement and coil testing
Cooling System: Radiator, thermostat, and water pump service
Exhaust System: Manifold, catalytic converter, and muffler repair

Transmission & Drivetrain

Automatic transmission and SH-AWD system service procedures.

Transmission Service: Fluid change procedure, filter replacement, shift solenoid testing.

SH-AWD System: Rear differential service, torque transfer unit maintenance, wheel speed sensor calibration.

Transmission Control Module: Diagnostic trouble codes, reset procedures, programming.

Suspension & Steering

Front and rear suspension components and power steering system repair.

Front strut replacement: Removal and installation procedure
Rear shock absorber: Service and replacement steps
Control arms and bushings: Inspection and replacement
Stabilizer bar and links: Removal and installation
Power steering pump: Service and bleeding procedure
Steering gear: Adjustment and replacement

Tip: Always perform wheel alignment after suspension component replacement.

Brake Systems

Disc brake system maintenance including ABS and electronic brake distribution.

Front brake pads: Replacement procedure and bedding process
Rear brake pads: Service and parking brake adjustment
Brake rotors: Measurement specifications and replacement
Brake fluid bleeding: Manual and pressure bleeding methods
ABS module: Diagnostic testing and component replacement
Brake booster: Testing and replacement procedure

WARNING! Always test brake system operation before road testing vehicle.

Electrical Systems

Wiring diagrams, component locations, and electrical system troubleshooting.

Battery and charging system: Alternator testing, battery replacement, voltage regulator service.

Starting system: Starter motor testing, solenoid replacement, ignition switch service.

Lighting systems: Headlight adjustment, bulb replacement, circuit testing.

HVAC & Climate Control

Heating, ventilation, and air conditioning system service procedures.

AC compressor: Removal, installation, and oil charging procedure

Heater core: Replacement steps and coolant system bleeding

Blower motor: Testing and replacement procedure

Climate control unit: Diagnostic testing and calibration

Body & Interior

Body panel replacement, interior component service, and glass installation.

Door panels: Removal and installation procedure
Seat removal: Front and rear seat service
Instrument panel: Component access and replacement
Glass replacement: Windshield and door glass installation
Exterior trim: Moldings and emblems replacement

Diagnostic Procedures

Using diagnostic tools and interpreting trouble codes for efficient repair.

OBD-II system: Code retrieval and clearing procedures

Factory scan tool: Advanced system diagnostics and programming

Component testing: Sensor and actuator testing procedures

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
Engine won't start	Battery, starter, fuel system	Check battery voltage, test starter, verify fuel pressure
Transmission slipping	Low fluid, worn clutches	Check fluid level and condition, test line pressure
Brake vibration	Warped rotors, worn pads	Inspect rotors for runout, replace pads and rotors
Electrical issues	Battery, alternator, grounds	Test charging system, check ground connections
AC not cooling	Refrigerant leak, compressor	Check refrigerant pressure, test compressor clutch

Technical Support: Contact Acura technical assistance for complex diagnostic issues.

Parts Information: Use genuine Acura parts for all repairs to maintain vehicle performance and safety.