2010 Acura TSX Repair Manual PDF

The 2010 Acura TSX Repair Manual provides comprehensive technical information for maintenance, repair, and troubleshooting of the 2010 Acura TSX sedan. This manual covers engine systems (2.4L I4), transmission (5-speed automatic/6-speed manual), electrical systems, suspension, brakes, steering, climate control, and body components. Below are key sections for specifications, maintenance procedures, troubleshooting, and repair instructions.

1. Vehicle Specifications 2. Maintenance Schedule 3. Engine System 4. Transmission 5. Electrical System 6. Suspension & Steering 7. Brake System 8. Climate Control 9. Body & Interior 10. Troubleshooting Guide

Vehicle Specifications

Key technical data for the 2010 Acura TSX including dimensions, capacities, and performance metrics.

Specification	Description
Engine	2.4L DOHC i-VTEC 4-cylinder
Horsepower	201 hp @ 7000 rpm
Torque	172 lb-ft @ 4400 rpm
Transmission	5-speed automatic / 6-speed manual
Fuel Capacity	18.5 gallons
Curb Weight	3450 lbs (approx)
Wheelbase	106.4 inches
Overall Length	183.3 inches
Brake System	4-wheel disc brakes with ABS
Fuel Economy	21 city / 30 highway (automatic)

Maintenance Schedule

Recommended maintenance intervals and service procedures for optimal vehicle performance.

Oil and filter change: Every 7,500 miles or 12 months
Tire rotation: Every 7,500 miles
Air filter replacement: Every 30,000 miles
Spark plug replacement: Every 105,000 miles
Brake fluid replacement: Every 3 years
Coolant replacement: Every 120,000 miles or 10 years
Transmission fluid: Every 30,000 miles (automatic)

WARNING! Always use genuine Acura parts and fluids for optimal performance and warranty compliance.

Engine System

Detailed repair and maintenance procedures for the 2.4L K24Z3 engine.

Engine Removal: Step-by-step procedure for engine removal and installation
Timing Chain: Inspection and replacement procedures
Valve Adjustment: Cold engine valve clearance specifications
Fuel System: Fuel pump replacement and injector service
Ignition System: Spark plug and coil replacement
Cooling System: Radiator, thermostat, and water pump service
Exhaust System: Catalytic converter and manifold procedures

Transmission

Service procedures for both automatic and manual transmission systems.

Automatic Transmission: Fluid change procedures, shift solenoid replacement, valve body service, torque converter inspection.

Manual Transmission: Clutch replacement, shift linkage adjustment, fluid specifications, synchronizer service.

Differential: Fluid change procedures and seal replacement for front differential.

Electrical System

Wiring diagrams, component locations, and repair procedures for electrical systems.

Battery: Testing and replacement procedures
Alternator: Output testing and replacement
Starter: Removal and installation
Lighting Systems: Headlight, taillight, and signal light replacement
Fuse Box: Locations and amperage specifications
ECU: Diagnostic trouble code reading and reset procedures
Audio System: Radio and speaker replacement

Tip: Always disconnect battery before performing electrical work.

Suspension & Steering

Repair procedures for front and rear suspension components and steering system.

Front Struts: Removal and installation with spring compressor
Rear Shocks: Replacement procedures
Control Arms: Bushings and ball joint replacement
Stabilizer Bars: Link and bushing replacement
Power Steering: Pump replacement and fluid bleeding
Alignment: Specifications and adjustment procedures
Wheel Bearings: Front and rear bearing replacement

WARNING! Use proper spring compression tools when working with struts.

Brake System

Complete brake system service including ABS diagnostics and repair.

Brake Pads: Front and rear pad replacement procedures
Brake Rotors: Measurement specifications and replacement
Brake Fluid: Bleeding procedures and fluid specifications
ABS System: Diagnostic trouble codes and component testing
Parking Brake: Adjustment and cable replacement
Brake Lines: Inspection and replacement procedures
Master Cylinder: Bench bleeding and installation

Climate Control

HVAC system repair and maintenance procedures.

Air Conditioning: Compressor replacement, refrigerant recovery and recharge, evaporator and condenser service.

Heating System: Heater core replacement, blend door actuator service, temperature control diagnosis.

Ventilation: Blower motor replacement, resistor testing, air distribution system.

Body & Interior

Body panel replacement, interior component service, and trim procedures.

Exterior: Bumper cover replacement, door panel service, mirror replacement, glass installation.

Interior: Dashboard components, seat removal and repair, console service, trim panel removal.

CAUTION! Use proper trim removal tools to avoid damage to plastic components.

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
Engine won't start	Battery, starter, fuel pump	Check battery voltage, test starter, listen for fuel pump prime
Poor acceleration	Clogged filter, fuel pump	Check air filter, fuel pressure, spark plugs
Brake vibration	Warped rotors	Measure rotor thickness and runout, replace if out of spec
Steering pull	Alignment, tire pressure	Check and adjust tire pressure, perform wheel alignment
AC not cooling	Refrigerant leak, compressor	Check refrigerant pressure, test compressor clutch
Electrical issues	Battery, alternator, grounds	Test charging system, check ground connections
Transmission slipping	Low fluid, worn clutches	Check fluid level and condition, scan for codes

Reset Procedures: Maintenance minder reset, ECU reset, window initialization.

Technical Support: Acura dealership service department or certified Acura technician.