Acura Legend Online Service Manual

The Acura Legend is a luxury sports sedan featuring advanced engineering, premium comfort features, and reliable performance. This online service manual covers maintenance procedures, technical specifications, troubleshooting guides, and repair instructions for various model years. Below are comprehensive sections for vehicle overview, maintenance schedules, technical specifications, diagnostic procedures, and repair instructions.

1. Vehicle Overview 2. Maintenance Schedules 3. Technical Specifications 4. Engine Systems 5. Transmission Systems 6. Electrical Systems 7. Brake Systems 8. Suspension & Steering 9. Heating & AC Systems 10. Diagnostic Procedures 11. Troubleshooting Guide

Vehicle Overview

Key components: V6 engine, automatic/manual transmission options, power steering, ABS brakes, climate control, and premium audio system.

ComponentDescription
Engine Type2.7L V6 SOHC 24-valve
Transmission4-speed automatic or 5-speed manual
Brake System4-wheel disc brakes with ABS
Suspension4-wheel independent double-wishbone
SteeringPower-assisted rack-and-pinion
Fuel SystemProgrammed Fuel Injection (PGM-FI)
Electrical12-volt system with 80-amp alternator
Climate ControlAutomatic temperature control
Audio SystemPremium sound with CD player
Safety FeaturesDual airbags, side impact protection

Maintenance Schedules

Follow recommended service intervals for optimal performance and longevity.

  1. Every 7,500 miles: Oil and filter change, tire rotation, fluid checks
  2. Every 15,000 miles: Air filter replacement, brake inspection, suspension check
  3. Every 30,000 miles: Spark plug replacement, transmission fluid change, coolant flush
  4. Every 60,000 miles: Timing belt replacement, fuel filter change, comprehensive inspection

WARNING! Use only Acura-approved fluids and genuine parts. Failure to follow maintenance schedules may void warranty.

Technical Specifications

Engine Systems

Comprehensive engine maintenance and repair procedures.

  1. Oil change procedure: Drain plug location, filter replacement, capacity specifications
  2. Spark plug replacement: Gap specifications, torque values, wire routing
  3. Timing belt service: Replacement intervals, alignment marks, tension adjustment
  4. Cooling system: Radiator flush, thermostat replacement, coolant specifications
  5. Fuel system: Fuel filter replacement, injector service, pressure testing

CAUTION! Always disconnect battery before working on electrical components. Use proper safety equipment.

Transmission Systems

Automatic and manual transmission service procedures.

ServiceProcedureSpecifications
Fluid ChangeDrain and fill procedureATF-Z1 for automatic, MTF for manual
Filter ServicePan removal and filter replacementReplace every 30,000 miles
Shift LinkageAdjustment and lubricationCheck for smooth operation
Clutch ServiceClutch replacement procedureInspect flywheel and pressure plate

Electrical Systems

Battery, charging, starting, and accessory electrical systems.

  1. Battery service: Testing, replacement, cable maintenance
  2. Alternator testing: Output voltage check, belt tension adjustment
  3. Starter motor: Removal and installation, solenoid testing
  4. Lighting systems: Headlight adjustment, bulb replacement procedures
  5. Fuse box locations: Main fuse panel, under-dash fuses, relay identification

Tip: Always use digital multimeter for electrical diagnostics. Check grounds for corrosion.

Brake Systems

ABS and conventional brake system maintenance.

  1. Brake pad replacement: Front and rear procedures, wear sensor reset
  2. Rotor service: Measurement specifications, resurfacing limits
  3. Brake fluid flush: Procedure, fluid specifications, bleeding sequence
  4. ABS diagnostics: Trouble code retrieval, sensor testing, module service
  5. Parking brake: Adjustment procedure, cable replacement

WARNING! Always replace brake components in axle sets. Test brake system after service.

Suspension & Steering

Front and rear suspension components and steering system.

ComponentInspectionReplacement
Struts/ShocksCheck for leaks and wearReplace in pairs
Ball JointsCheck for play and wearPress-fit replacement
Tie Rod EndsCheck for loosenessThread count alignment
Control ArmsBushings and ball jointsComplete assembly
Power SteeringFluid level and conditionPump and rack service

Heating & AC Systems

Climate control system maintenance and repair.

  1. AC system service: Pressure testing, refrigerant recovery and recharge
  2. Compressor replacement: Belt removal, clutch service, oil capacity
  3. Heater core: Replacement procedure, coolant drain and fill
  4. Blower motor: Removal and testing, resistor replacement
  5. Control panel: Diagnosis and repair of electronic controls

CAUTION! AC system contains high pressure refrigerant. Use proper recovery equipment.

Diagnostic Procedures

Using diagnostic tools and interpreting trouble codes.

  1. OBD-II connector location: Under driver's side dash
  2. Code retrieval: Using scan tool or flash code method
  3. Live data monitoring: Sensor values, system parameters
  4. Component testing: Resistance checks, voltage measurements
  5. System reset procedures: Clearing codes and adaptations

Troubleshooting Guide

SymptomPossible CauseCorrective Action
Engine won't startBattery, starter, fuel pumpCheck battery voltage, listen for fuel pump, test starter
Poor fuel economyO2 sensors, air filter, tiresReplace O2 sensors, check air filter, verify tire pressure
Brake vibrationWarped rotors, worn padsResurface or replace rotors, install new pads
AC not coolingRefrigerant leak, compressorPressure test system, check compressor clutch
Electrical issuesAlternator, battery, groundsTest charging system, clean battery terminals
Transmission slippingLow fluid, worn clutchesCheck fluid level and condition, diagnose internal issues

Reset Procedures: Battery disconnect for ECU reset, maintenance reminder reset procedure

Technical Support: Contact Acura customer service at 1-800-382-2238 or visit acura.com

Acura Legend Online Service Manual © - All Rights Reserved 2025