Acura RDX 2016 Door Edge Protector Installation Manual

The Acura RDX 2016 Door Edge Protector is designed to protect your vehicle's door edges from dings, scratches, and chips caused by parking lot incidents, garage walls, and other obstacles. This installation guide provides step-by-step instructions for proper installation, including surface preparation, alignment techniques, and finishing tips to ensure optimal protection and appearance.

1. Product Overview 2. Tools Required 3. Surface Preparation 4. Installation Steps 5. Alignment Guidelines 6. Finishing & Inspection 7. Care & Maintenance 8. Troubleshooting 9. Warranty Information

Product Overview

The door edge protector kit includes four protectors (two front doors, two rear doors) made from durable polyurethane with 3M automotive-grade adhesive backing, designed specifically for Acura RDX 2016 model contours.

Component	Description
Front Door Protectors	2 pieces, 32-inch length each
Rear Door Protectors	2 pieces, 28-inch length each
3M Adhesive Backing	Pre-applied, high-strength automotive adhesive
Alignment Template	Paper guide for precise positioning
Cleaning Wipes	Isopropyl alcohol wipes for surface preparation
Application Squeegee	Rubber tool for smooth installation

Tools Required

Gather these tools before beginning installation:

Clean microfiber cloths
Measuring tape
Masking tape (for temporary positioning)
Scissors (if trimming required)
Hair dryer or heat gun (for cold weather installation)

NOTE: Work in a clean, dry area with temperatures above 60°F (15°C) for optimal adhesive performance.

Surface Preparation

Proper surface preparation is critical for long-lasting adhesion.

Clean door edges thoroughly with included alcohol wipes
Remove all wax, grease, and debris from door edge surfaces
Allow surfaces to dry completely (5-10 minutes)
Do not touch cleaned surfaces with bare hands

WARNING! Failure to properly clean surfaces may result in adhesive failure and protector detachment.

Installation Steps

Follow these steps for each door protector:

Peel back 2-3 inches of adhesive backing paper
Align protector with door edge using alignment template
Press initial section firmly into place
Slowly peel remaining backing while pressing protector onto surface
Use squeegee to remove air bubbles and ensure full contact
Apply firm pressure along entire length for 30 seconds

CAUTION! Do not stretch the protector during installation as this may cause premature failure.

Alignment Guidelines

Proper alignment ensures optimal protection and appearance.

Front Doors: Align protector flush with door edge, centered between hinges and latch
Rear Doors: Position protector to cover entire vulnerable edge area
Gap Measurement: Maintain consistent 1/8-inch gap from door panel seam
Visual Check: Step back and verify alignment before final adhesion

Finishing & Inspection

Complete installation with these finishing steps:

Inspect each protector for proper adhesion and alignment
Check for air bubbles and press out with squeegee
Ensure protector ends are securely attached
Verify smooth transition between protector and door surface
Do not open/close doors for 24 hours to allow adhesive to cure

Tip: Use hair dryer on low heat to improve adhesion in cool conditions.

Care & Maintenance

Proper care ensures long-lasting protection.

Clean with mild soap and water; avoid abrasive cleaners and high-pressure washers directed at edges. Do not apply wax or sealants to protector surfaces.

CAUTION! Avoid using silicone-based products near protectors as they may compromise adhesion.

Troubleshooting

Issue	Possible Cause	Solution
Protector lifting at ends	Insufficient surface preparation	Remove, re-clean surface, reapply with firm pressure
Air bubbles under protector	Improper application technique	Use squeegee to push bubbles toward nearest edge
Protector not adhering	Cold temperatures or contaminated surface	Warm area with hair dryer; ensure surface is clean and dry
Misaligned installation	Rushed positioning	Carefully remove and reapply using alignment guide
Adhesive residue after removal	Normal with aged installation	Use automotive adhesive remover and clean cloth

Warranty Information

This Acura RDX 2016 Door Edge Protector is backed by a 3-year limited warranty against manufacturing defects and material failure. Warranty does not cover improper installation, accident damage, or normal wear and tear. For warranty claims, contact customer service with proof of purchase and installation date.

Support: 1-800-ACURA-HELP; www.acura.com/accessories