Factory Service Repair Manual 2014 Acura TSX

The Factory Service Repair Manual for the 2014 Acura TSX provides comprehensive technical information, maintenance procedures, and repair instructions for automotive technicians and DIY enthusiasts. This manual covers all major systems including engine, transmission, suspension, brakes, electrical, and body components for the 2014 Acura TSX models with 2.4L I4 and 3.5L V6 engines. Below are key sections for technical specifications, maintenance schedules, repair procedures, diagnostic troubleshooting, and safety precautions.

1. Vehicle Identification 2. Maintenance Schedules 3. Engine Systems 4. Transmission 5. Suspension & Steering 6. Brake Systems 7. Electrical Systems 8. Body & Interior 9. Diagnostic Procedures 10. Special Tools 11. Troubleshooting

Vehicle Identification

Key identification components: VIN locations, model codes, engine identification, transmission types, production dates.

Component	Location/Description
VIN Plate	Driver's side dashboard visible through windshield
Engine Code	K24Z7 (2.4L) / J35Z2 (3.5L) stamped on engine block
Transmission Codes	5-speed Automatic / 6-speed Manual
Production Date	Manufacturer's label on driver's door jamb
Paint Code	Label in glove compartment or driver's door jamb
Trim Levels	Base, Technology Package, Special Edition

Maintenance Schedules

Recommended service intervals and maintenance procedures.

Oil Change: Every 7,500 miles or 12 months (synthetic)
Tire Rotation: Every 7,500 miles
Air Filter: Every 30,000 miles
Brake Fluid: Every 3 years regardless of mileage
Transmission Fluid: Every 60,000 miles (automatic)
Spark Plugs: Every 105,000 miles
Timing Belt: Every 105,000 miles (3.5L V6)

WARNING! Always use Honda/Acura genuine parts and recommended fluids. Failure to follow maintenance schedules may void warranty.

Engine Systems

Engine Types: 2.4L I4 K24Z7 (201 hp) / 3.5L V6 J35Z2 (280 hp)
Fuel System: Programmed Fuel Injection (PGM-FI)
Ignition System: Direct ignition system with individual coils
Cooling System: Pressurized with electric fan
Lubrication System: Wet sump with gear-type oil pump
Compression Ratio: 11.0:1 (2.4L) / 10.5:1 (3.5L)
Oil Capacity: 4.4 quarts (2.4L) / 5.0 quarts (3.5L)

Transmission

Service procedures for 5-speed automatic and 6-speed manual transmissions.

Automatic: BAYA/BYBA 5-speed with SportShift, torque converter service, valve body repair, fluid replacement procedure.

Manual: 6-speed with helical gears, synchronizers, clutch hydraulic system, shift linkage adjustment.

Transmission fluid capacity: 2.9 quarts (automatic) / 2.4 quarts (manual). Recommended fluid: Honda/Acura ATF-Z1 (automatic) or MTF (manual).

Suspension & Steering

Front: MacPherson strut with lower L-arms, coil springs, stabilizer bar. Rear: Multi-link double wishbone with coil springs.

Strut replacement procedure and alignment specifications
Control arm bushing inspection and replacement
Stabilizer bar and link rod service
Power steering system: Electric power steering (EPS) diagnosis
Wheel alignment specifications: Camber, caster, toe angles

Tip: Always perform wheel alignment after suspension component replacement.

Brake Systems

Four-wheel disc brakes with ABS, VSA, and EBD.

Front brakes: 11.8-inch ventilated discs, single-piston calipers
Rear brakes: 11.1-inch solid discs, single-piston calipers
Brake pad replacement procedure and bedding-in process
Rotor machining specifications and minimum thickness
ABS modulator service and bleeding procedure
Brake fluid specification: DOT 3 or DOT 4

WARNING! Always bleed brakes in correct sequence and never reuse brake fluid.

Electrical Systems

12-volt negative ground system with 70-amp main fuse.

System	Specifications
Battery	12V 51Ah, located in trunk
Alternator	120A (2.4L) / 150A (3.5L)
Starter	1.4 kW reduction type
Fuse Boxes	Under-hood, driver's side interior, trunk
Lighting	HID headlights (Technology Package), LED taillights

Body & Interior

Body dimensions, panel alignment, interior trim removal procedures.

Door panel removal, dashboard components, seat disassembly, glass replacement, exterior trim. Body repair specifications: panel gaps, welding procedures, corrosion protection.

Diagnostic Procedures

Using Honda Diagnostic System (HDS) or equivalent scan tool.

Connecting to OBD-II port under driver's dashboard
Reading and clearing DTCs (Diagnostic Trouble Codes)
Active tests and system monitoring
Data list parameters and normal values
ECM/PCM reprogramming procedures

CAUTION! Always disconnect battery before electrical repairs. Follow proper safety procedures.

Special Tools

Required Acura/Honda special service tools for proper repairs.

Crankshaft pulley holder 07MAB-PY3010A
Valve adjustment tool 07PAJ-001000A
Piston ring compressor 07NAD-PX40000
Ball joint separator 07MAC-SL00200
Steering wheel puller 07AAF-SD40100
CV boot clamp tool 07JAF-PH80100

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Battery, starter, fuel pump	Check battery voltage, listen for fuel pump prime, test starter circuit
Check engine light on	Various sensors, emissions	Scan for DTCs, inspect related sensors and wiring
Transmission shifting hard	Fluid level, solenoids	Check fluid level and condition, test shift solenoids
Brake pulsation	Warped rotors	Measure rotor thickness and runout, replace or machine rotors
Electrical issues	Ground connections, fuses	Check main grounds, inspect fuse boxes for corrosion

Reset Procedures: Maintenance minder reset, ECM/PCM reset, power window reset.

Technical Support: Acura Technical Information System 1-888-ACURA-TS